Drony
Producenci
Koszyk0,00 zł
HappyModel Mobula8 2S 85mm Digital HD DJI O3/Walksnail/Hdzero
499,77 zł
Brutto
Produkty powiązane
HappyModel Mobula8 Digital
DJI O3/Walksnail/Hdzero
Mobula8 w wersji cyfrowej to jeden z najmniejszych modeli dronów FPV z obrazem cyfrowym. Mobula8 to rewelacyjny dron będący zwieńczeniem całej serii modeli Mobula powstałych na przestrzeni kilku lat. Dzięki temu Mobula8 HD to niezwykle wyżymała konstrukcja o świetnych właściwościach lotnych. Mimo niepozornego wyglądu posiada zaawansowaną elektronikę o wręcz niesamowitych jak na swój rozmiar osiągach. Mobula8 HD to model whoopa z kilkoma nadajnikami VTX do wyboru. Każdy model posiada wbudowany odbiornik ELRS.
Spare parts specifications:
| Motor | Mode: EX1103 KV11000 Configu-ration:9N12P Stator Diamter:11mm Stator Length:3mm Shaft Diameter:Φ1.5mm Motor Dimension(Dia.*Len):Φ13.5mm*15.5mm Weight(g):3.8g No.of Cells(Lipo):1-2S |
| Propellers | Weight:0.88g Material: PC Pitch:2.3inch Props Dia:52.17mm Center Thickness:5mm Center Hole Dia:1.5mm |
| Flight controller | MCU: STM32F405RGT6 (168MHZ, 1Mbyte FLASH) GYRO Sensor: BMI270 (SPI connection) Mount hole size: 25.5mm*25.5mm Power supply: 1-2S battery input (DC 2.9V-8.7V) Built-in 12A(each) Blheli_S 4in1 ESC Built-in Serial ExpressLRS 2.4G Built-in BMP280 Barometer Built-in 8MBp blackbox Built-in voltage meter sensor , voltage meter scale 110 Built-in current meter sensor , current meter scale 470 |
| Onboard 4in1 ESC | Power supply: 1-2S LiPo/LiPo HV Current: 12A continuous peak 15A (3 seconds) Support BLHeli_S Bluejay firmware Factory firmware: Bluejay ESC V0.19 Firmware target: Z-H-30 Default protocol: DSHOT300 When use 1s battery and high KV 0702/0802 motors, should set startup power to 1100/1200 |
| Onboard UART ExpressLRS 2.4GHz Receiver | Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz RF Frequency: 2.4GHz Antenna: enameled copper wire 31mm length Telemetry output Power: <12dBm Default firmware version: ExpressLRS V3.0.1 Firmware target: HappyModel EP 2400 RX Could update firmware via ExpressLRS configurator |
| DJI O3 Air Unit | Works with DJI FPV Goggles V2, DJI Goggles 2, and DJI FPV Remote Controller 2 D-Cinelike mode for Vivid Colors Flagship O3+ Video Streaming Customizable Canvas Mode 155° Super-Wide FOV 1/1.7-Inch Sensor Compact in Size |
| Walksnail version | Camera Model Avatar lite camera Image Sensor 1/2.7”1nch Resolution 1080P/60fps,720P/120fps,720P/60fps Ratio 16/9 4/3 Lens 2.1mm FOV 170° Aperture F2.0 Shutter Rolling Rolling shutter Min.Illumination 0.001Lux Weight 1.8g Dimensions 14*14*16mm VTX Model Avatar mini 1s module Communication Frequency 5.725-5.850GHz Transmitter Power (EIRP) FCC:<25.5dBm;CE:<14dBm;SRRC:<20dBm; MIC:<25dBm I/O Interface JST1.0*6(Power in)JST0.8*4(USB) Mounting Holes 25.5*25.5mm Dimensions 30*30*6.5mm Storage 8G Recording 1080p/720p Weight 5.1g Operating Temperature -20-40℃ Channels 8 Wide Power Input 3.1V-5V Supported FC System Betaflight OSD Canvas mode Bitrate 25mbps 50mbps Latency Average delay 22ms Antenna IPEX |
| HDZERO Version | HDZero Nano Lite Camera 14x16x11 mm 1.5gram 0.5 inch, up to 10650 mV/Lux-sec ultra-high sensitive CMos sensor Excellent low light performance Fov: 4:3: D:130° H:108° v:84° 16:9:D:122° H:108° V:65° HDZero Whoop Lite VTX 1-3S Input 25mW/200mW RF Output-SmartAudio Support 25.5×25.5 M2 Soft Mounting- Antenna Retention Removable Shielding Box- 32.5×32.5mm(29x29mm inner) 4.5grams/4mm Thickness (without shielding) |
Na razie nie dodano żadnej recenzji.
Sprawdz to!
